Skip to main content

Oregon Route 62 Rogue Valley Expressway

By

Much of Oregon Route 62 recently in the Medford Area has been moved from Crater Lake Highway to the Rogue Valley Expressway. 

The Rogue Valley Expressway is a 4.5 mile segment of Oregon Route 62 ("OR 62") which is a limited access bypass of Crater Lake Highway.  The Rogue Valley Expressway begins just south of OR 140 and terminates about a half mile from Interstate 5 ("I-5").  The Rogue Valley Expressway was intended to expedite travel between Medford and White City.  


Part 1; the background of the Rogue Valley Expressway

Much of the history of the Rogue Valley Expressway is discussed in the May issue of ODOT Moving Ahead.  According to ODOT Moving Ahead concepts to move OR 62 from Crater Lake Highway between Medford and White City began to emerge in the 1990s  In 2004 project teams met to narrow down the possible design concepts which would be evaluated for Environmental Impact Statements.  The Rogue Valley Expressway was funded in 2009 via $120 million dollars set aside as part of the Oregon Jobs & Transportation Act.  Construction of the Rogue Valley Expressway began in May 2016 and would open to traffic as mainline OR 62 in May 2019.  



 

Part 2; a drive on the Rogue Valley Expressway

As noted above OR 62 joins the Rogue Valley Expressway just south of OR 140 and White City.  OR 62 westbound makes a right turn off of Crater Lake Highway onto the Rogue Valley Expressway.  The former surface alignment of OR 62 on Crater Lake Highway is signed OR 62 Business.  




Despite being fully limited access and not having any interchanges the Rogue Valley Expressway is signed at a typical Oregon 55 MPH urban freeway speed.


The Rogue Valley Expressway makes a southward jog towards Medford and enters the City Limits at Vilas Road overpass. 





The Rogue Valley Expressway skirts the eastern edge of Rogue Valley International-Medford Airport and merges back into Crater Lake Highway approaching I-5. 









Labels:

Comments

Unknown said…
This comment has been removed by the author.
1:54 AM
Jonathan/Beaver State Roads said…
According to the first draft map, the bypass was going to extend further up current OR-62 to White City. There would have been interchanges at Vilas Road, OR-62 (at or near the current northern end of the bypass) and OR-140 (as a cloverleaf). The 2013 FEIS selected a different longer routing: White City would be bypassed to the west to Dutton Road, eliminating the 140 cloverleaf but adding partial interchanges at existing OR-62 at both ends of White City. The interchange at Vilas road also changed from an SPUI to a tight diamond interchange. At some point, the project was rolled back or split into phase; the Vilas Road interchange was removed, and the bypass now ends at OR-62 between Corey Road and Gregory Road.
1:55 AM
Post a Comment

Popular posts from this blog

Grand Loop Road of Yellowstone National Park

By
  Grand Loop Road is a 140 mile loop highway which traverses the interior of Yellowstone National Park.  Grand Loop Road connects all of the major attractions and geological features of Yellowstone National Park along with the entrance roads.  Grand Loop Road is a seasonal highway and despite some conjecture never has been part of the US Route System.   Part 1; the history of Grand Loop Road The majority of history pertaining to Grand Loop Road was taken from the below National Park Service article: Historic Roads - Yellowstone National Park (U.S. National Park Service) (nps.gov) Yellowstone was declared the first National Park of the United States on March 1st, 1872.  The first real highway to access Yellowstone National Park came in 1873 when a tolled facility was constructed from Bozeman, Montana via Yankee Jim Canyon to Mammoth Hot Springs.  Numerous attempts were made to fund construction of roadway infrastructure during the early years of Yellows...
Post a Comment
Read more

The last 1956-63 era California Sign State Route Spade?

By
Along southbound California State Route 170 (the Hollywood Freeway Extension) approaching the Hollywood Freeway/Ventura Freeway interchange a white California State Route 134 Sign State Route Spade can be observed on guide sign.  These white spades were specifically used during the 1956-63 era and have become increasingly rare.  This blog is intended to serve as a brief history of the Sign State Route Spade.  We also ask you as the reader, is this last 1956-63 era Sign State Route Spade or do you know of others?  Part 1; the history of the California Sign State Route Spade Prior to the Sign State Route System, the US Route System and the Auto Trails were the only highways in California signed with reassurance markers.  The creation of the US Route System by the American Association of State Highway Officials during November 1926 brought a system of standardized reassurance shields to major highways in California.  Early efforts to create a Sign State Route ...
Post a Comment
Read more

California State Route 70; the Feather River Highway

By
From 2017 through to early 2019 I drove the majority of the California State Route 70; the Feather River Highway from CA 89 southwest to CA 99. CA 70 is an approximately 178.5 mile state highway which starts at US 395 near the Nevada State Line and travels west through the Feather River Canyon to CA 99.  CA 70 is often referred to as the Feather River Highway" given it's close association with the river.  Historically CA 70 was previously signed as US 40A and CA 24.  The Legislative Routes prior to the 1964 California Highway Renumbering that made up the current route of CA 70 are as follows: -  Legislative Route Number 21 from US 395 westward to Oroville. -  LRN 87 from Oroville south to Marysville. -  LRN 232 from Marysville to the current junction with CA 99.  CA 70 was even dual signed with CA 99 into Sacramento on what was LRN 232 for a time. The change from US 40A/LRN 21/LRN 87/LRN 232 can be seen by comparing the 1963 State Highway Ma...
Post a Comment
Read more