Skip to main content

Yes, the color of your nearby fire hydrant matters...

...and here's why.

You will find White, Red, Yellow and Violet colored fire hydrants pretty much everywhere.  But there's a reason for this - and it's because of the National Fire Protection Association (NFPA).  This association has issued guidelines for color coding standards for fire hydrants.  These color codes from the body of the hydrant, top of the hydrant, and in some municipalities the outlet caps are designed to allow fire fighters to know what type of system, water flow rate (Gallons Per Minute or GPM), and level of water pressure.  This guideline is known as NFPA 291 and is intended to be used universally throughout the United States.

The NFPA guidelines are specific to the body and the top cap of the hydrant.  If a hydrant is WHITE or YELLOW - it means that it is connected to a public/municipal water system.  If a hydrant is RED - the hydrant is connected to a private system, typically a well.  These are most common in rural or unincorporated areas. Red is a recommendation by the NFPA - the guideline is that it should be a color that distinguishes itself from the public system.  Finally, PURPLE hydrants means that the hydrant is connected to a non-potable water supply.

Our fire hydrant conversion in progress
The top cap color is meant to signify the water flow rate or GPM of the hydrant.  A BLUE top means that the water flow rate is over 1500 GPM.  GREEN is for a flow rate of 1,000 - 1,499 GPM and is acceptable for most residential areas.  ORANGE is a rate of 500 - 999 GPM and is considered marginally adequate.  Finally, RED is a flow rate of below 500 GPM and is considered inadequate to fight fires. 

Again, these are only guidelines as many municipalities have added colors for water pressure levels or use a different color for hydrants connected to a public system.

Earlier this year, the fire hydrant in front of our home changed from red to yellow.  The photos in the entry chronicle the transformation from red to yellow and silver.  You'd think that it wouldn't be noticed, but our neighborhood message board were filled with questions asking why their fire hydrant was being repainted and why does it have to be yellow.   Even a year later, the repainting of the hydrants were still being talked about.




https://twitter.com/WNFIV/status/938093442512637955The reason is that all hydrants connected to the City of Raleigh water system were being painted yellow to meet the NFPA 291 guidelines.  This included municipalities throughout Wake County - such as Wake Forest, Knightdale, Garner - that receive water from the Raleigh system.  It was also noted that municipalities could qualify for lower insurance rates if they follow the NFPA guidelines.

The finished product.
So the next time you see a fire hydrant.  Check the colors of it - it may be telling you something.  Especially if it is purple!

Comments

Unknown said…
Hi Tom F.

Hah, back in 1976, 1 year out of the Navy I moved to Manhattan Beach. My new neighbors joined me for a summer drinking fest. We lived about 5 blocks up and got soooo drunk, we started opening our common area hydrant to cars passing by. Our mission? Cool off the people, it was very hot out.

Needless to say, a few got busted, tossed into the drunk tank, me among them. My fine was no jail and 10 days community service and given three buckets of paint. Guess what my fine was? I learned a lot about the color codes...up close and personal.

Popular posts from this blog

Memphis & Arkansas Bridge (Memphis, TN)

  Like the expansion of the railroads the previous century, the modernization of the country’s highway infrastructure in the early and mid 20th Century required the construction of new landmark bridges along the lower Mississippi River (and nation-wide for that matter) that would facilitate the expected growth in overall traffic demand in ensuing decades. While this new movement had been anticipated to some extent in the Memphis area with the design of the Harahan Bridge, neither it nor its neighbor the older Frisco Bridge were capable of accommodating the sharp rise in the popularity and demand of the automobile as a mode of cross-river transportation during the Great Depression. As was the case 30 years prior, the solution in the 1940s was to construct a new bridge in the same general location as its predecessors, only this time the bridge would be the first built exclusively for vehicle traffic. This bridge, the Memphis & Arkansas Bridge, was completed in 1949 and was the third

Old River Lock & Control Structure (Lettsworth, LA)

  The Old River Control Structure (ORCS) and its connecting satellite facilities combine to form one of the most impressive flood control complexes in North America. Located along the west bank of the Mississippi River near the confluence with the Red River and Atchafalaya River nearby, this structure system was fundamentally made possible by the Flood Control Act of 1928 that was passed by the United States Congress in the aftermath of the Great Mississippi River Flood of 1927 however a second, less obvious motivation influenced the construction here. The Mississippi River’s channel has gradually elongated and meandered in the area over the centuries, creating new oxbows and sandbars that made navigation of the river challenging and time-consuming through the steamboat era of the 1800s. This treacherous area of the river known as “Turnbull’s Bend” was where the mouth of the Red River was located that the upriver end of the bend and the Atchafalaya River, then effectively an outflow

California State Route 203 the proposed Minaret Summit Highway

California State Route 203 is an approximately nine-mile State Highway located near Mammoth Lakes in the Sierra Nevada Mountains of Mono County.  California State Route 203 as presently configured begins at US Route 395, passes through Mammoth Lakes and terminates at the Madera County line at Minaret Summit.  What is now California State Route 203 was added to the State Highway System in 1933 as Legislative Route Number 112.  The original Mammoth Lakes State Highway ended at Lake Mary near the site of Old Mammoth and was renumbered to California State Route 203 in 1964.  The modern alignment of the highway to Minaret Summit was adopted during 1967.   The corridor of Minaret Summit and Mammoth Pass have been subject to numerous proposed Trans-Sierra Highways.  The first corridor was proposed over Mammoth Pass following a Southern Pacific Railroad survey in 1901.  In 1931 a corridor between the Minarets Wilderness and High Sierra Peaks Wilderness was reserved by the Forest Service for po